1973 Dodge Challenger Ps Pdb V8 Automatic Slick Paint See Video S on 2040-cars

Auto blog

Chrysler recalling over 200k vehicles across its brands

With more than 200,000 units across six separate recalls and almost all of its brands, it appears that Chrysler has officially jumped headfirst into the recall pool this month. The National Highway Traffic Safety Administration has issued three official recalls for the automaker, and The Detroit News is reporting that the automaker itself has announced three more.
The biggest of the recalls applies to about 120,000 Dodge Charger, Dodge Challenger and Chrysler 300 models for 2011 and 2012 due to faulty wiring harnesses for the seat-mounted side airbags, which could lead to these airbags not deploying in the event of a crash. A little more than 60,000 two-wheel-drive versions of the 2007-2008 Dodge Nitro and 2008 Jeep Liberty SUVs are being recalled due to a heat shield that could cause the driveshaft to break, which if that isn't bad on its own, could then hit underneath where the airbag sensor is mounted, causing the airbags to deploy. Wrapping up NHTSA's recall notices, about 20,000 Jeep Patriot and Jeep Compass models for 2012 are also being recalled due to a problem with the fuel tank transfer tube that could lead to the vehicle stalling. The LX car recall campaign is going into effect this month, while the other two will start next month - all three notices are posted below.
In addition to the official NHTSA recalls, The Detroit News is also reporting that Chrysler is recalling more than 16,000 Ram trucks and a small number of Dodge Dart sedans. Around 6,500 2013 Ram 1500 trucks will be recalled due to an improper adjustment of the parking brake cable from the factory, while 7,000 Cummins-powered 2013 Ram Heavy Duty trucks are being recalled due to an engine cover that does not have as much heat resistance as it is supposed to. Finally, a total of 46 Dodge Dart sedans are being recalled due to a problem with the brake calipers and/or parking brake.

Dodge Charger Hellcat hitting 60 in 2.9 seconds on drag radials?

The Dodge boys and their cousins from SRT have shoehorned the same 707-horsepower, 6.2-liter supercharged V8 into both the Dodge Challenger and Charger. The former being a two-door, it's lighter than the latter four-door sedan. So it would stand to reason that the Dodge Challenger SRT Hellcat would be the quicker of the two, right?
Only that's not necessarily proving to be the case. On stock rubber, yes, the coupe beats the sedan: Dodge quotes a 0-60 time of 3.7 seconds for the Charger SRT Hellcat and 3.5 for the Challenger. Same gap across the quarter-mile: 11 seconds flat for the Charger versus 10.8 seconds for the Challenger. But according to recent reports, the story changes when you put both on drag radials.
While visiting Chrysler HQ in Auburn Hills, MI, TorqueNews.com caught wind of performance figures for the Charger Hellcat on drag tires: 0-60 in a mind-blowing 2.9 seconds and a quarter-mile in just 10.7. The latter figure just barely pips the Hellcat-powered Challenger's NHRA-certified figure of 10.8, making the Charger not only the fastest sedan on the market, but also the fastest muscle car. What isn't immediately clear, however, is whether the drag radials in question have any tread on them and are street-legal, or if they're pure slicks confined to a closed strip.

Dodge Viper to out-Hell the Hellcat with supercharged V10?

The Viper wouldn't be the Viper if it wasn't the most powerful model under the Chrysler umbrella. But with the arrival of the Hellcat engine in the Dodge Charger and Challenger, the Viper has fallen behind in the bragging rights department: where the new supercharged V8 produces 707 horsepower and 650 pound-feet of torque, the naturally aspirated V10 offers "only" 640 hp and 600 lb-ft - gargantuan output figures by almost any other standard, but crucially behind on the SRT power scale. Conner Avenue is going to have to do something about that.
Although the Hellcat's engine reportedly won't fit under the Viper's hood, SRT is now rumored to have another trick up its sleeve: supercharge the existing V10. According to the Pentastar performance enthusiasts at allpar.com, Chrysler has already taken delivery of the first such prototype engines so that it can begin the process of fitting it into an upgraded Viper.
The spooled ten-pot is tipped to produce around 800 hp and 650 lb-ft of torque. More than that and the Viper's drivetrain, chassis and bodywork would have to be substantially reworked. Though beefier transmissions are available, fitting them would reportedly set off a domino-game of changes required to handle the added torque. Which may be something Chrysler would be prepared to do for the next-generation model, but in the meantime, 800 hp could prove enough to put the Viper back atop the Mopar performance ladder where it belongs, and give it an edge against the new Corvette Z06 to rekindle sales.