2005 Dodge Dakota St Extended Cab Pickup 4-door 3.7l on 2040-cars

Auto blog

Chrysler recalls AWD 300, Charger, Ram 1500 over ZF transmission

What do the Chrysler 300, Dodge Charger and Ram 1500 all have in common? Yes, they're all Chrysler products, and two of them are based on the same platform. And we're sure you could find more similarities between them all, but the common trait we're looking at here is that, while they all come standard in rear-drive form, they're also available with all-wheel drive. And it's the transmission in those models that's the subject of the latest recall notice issued by the National Highway Traffic Safety Administration.
The output shaft on the eight-speed automatic transmission supplied by ZF to Chrysler for the AWD versions of the 300, Charger and Ram 1500 is apparently prone to fracture. That in the end could leave the vehicle without power and could, according to the NHTSA investigation, increase the chance of a crash. The vehicle could also roll away if even if left in Park without the handbrake applied.
That's why Chrysler is calling in 4,194 examples of those three models from the 2013 model year. Dealers will be responsible for inspecting the transmissions and, where necessary, replace the entire unit. See the full recall notice below for all the details.

Dodge Viper to out-Hell the Hellcat with supercharged V10?

The Viper wouldn't be the Viper if it wasn't the most powerful model under the Chrysler umbrella. But with the arrival of the Hellcat engine in the Dodge Charger and Challenger, the Viper has fallen behind in the bragging rights department: where the new supercharged V8 produces 707 horsepower and 650 pound-feet of torque, the naturally aspirated V10 offers "only" 640 hp and 600 lb-ft - gargantuan output figures by almost any other standard, but crucially behind on the SRT power scale. Conner Avenue is going to have to do something about that.
Although the Hellcat's engine reportedly won't fit under the Viper's hood, SRT is now rumored to have another trick up its sleeve: supercharge the existing V10. According to the Pentastar performance enthusiasts at allpar.com, Chrysler has already taken delivery of the first such prototype engines so that it can begin the process of fitting it into an upgraded Viper.
The spooled ten-pot is tipped to produce around 800 hp and 650 lb-ft of torque. More than that and the Viper's drivetrain, chassis and bodywork would have to be substantially reworked. Though beefier transmissions are available, fitting them would reportedly set off a domino-game of changes required to handle the added torque. Which may be something Chrysler would be prepared to do for the next-generation model, but in the meantime, 800 hp could prove enough to put the Viper back atop the Mopar performance ladder where it belongs, and give it an edge against the new Corvette Z06 to rekindle sales.

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.